Other

Campagnolo Pulley Assemblies - Drivetrain Speeds: 10 - Does not fit 2004-2008 Record 10 speed (carbon pulley cage)

Campagnolo Return Spring Caliper Brake Part

EPS cable guide magnets are required for internally routing EPS wires. - Includes: wire, metal cable, and magnet

Campagnolo Cassette Lockrings. - Fits 2000 and newer Campagnolo wheels - Fits all Fulcrum wheels - Fits 1999 Record/Chorus hubs and all Campy hubs 2000-newer - 27.0mm thread OD - For use only with Campagnolo 11-speed cassettes with 12 tooth first position cogs

Campagnolo Rear Recessed Pivot Bolt Assembly Caliper Brake Part

Desgined to increase the stiffness of the EPS front derailleur on frames with flexible braze-on mounts, especially frames with carbon fiber mounts. - Required for use on carbon frames with carbon front derailluer braze on mounts

Campagnolo Pulley Assemblies

A higher quality spring greatly improves the performance of your coil shock. VALT springs from Cane Creek are much lighter than traditional steel springs while pushing the boundaries of performance and durability. - Inner diameter of 36.5mm is compatible with all Cane Creek coil shocks - Also compatible with Manitou, Marzocchi, XFusion, ELKA/MRP, BOS and DSP - Compatible with Fox coil shocks with required spring clip adaptor

All CeramicSpeed Bearings are hand-built in Denmark. Super-smooth CeramicSpeed grade 3 Silicone Nitride balls are matched (within microns) with hardened steel raceways that feature an ultra-smooth polished groove. The balls are held in place by a reinforced polyamide cage. Every bearing is optimized with a low-viscosity CeramicSpeed All Round Grease to minimize friction and increase bearing life. Non-contact seals complete the bearings, keeping dirt and moisture out. CeramicSpeed Bearings can be used for any cycling discipline: Road, TT, Tri, Track, Cross, and MTB. The benefits are super low friction, better power transfer, and increased bearing life. During the building process, we check each bearing four times by hand to ensure that all parts are matched perfectly. CeramicSpeed Balls are 400% smoother, 128% harder, and 58% lighter than standard steel bearings normally used in the bicycle industry. When comparing the CeramicSpeed Balls with other ceramic balls in the industry, you will find that the CeramicSpeed Balls are 15% harder, take 99% higher loads, and are 100% smoother. - Inner Diameter: 15mm - Outer Diameter: 24mm - Width: 5mm

All CeramicSpeed Bearings are hand-built in Denmark. Super-smooth CeramicSpeed grade 3 Silicone Nitride balls are matched (within microns) with hardened steel raceways that feature an ultra-smooth polished groove. The balls are held in place by a reinforced polyamide cage. Every bearing is optimized with a low-viscosity CeramicSpeed All Round Grease to minimize friction and increase bearing life. Non-contact seals complete the bearings, keeping dirt and moisture out. CeramicSpeed Bearings can be used for any cycling discipline: Road, TT, Tri, Track, Cross, and MTB. The benefits are super low friction, better power transfer, and increased bearing life. During the building process, we check each bearing four times by hand to ensure that all parts are matched perfectly. CeramicSpeed Balls are 400% smoother, 128% harder, and 58% lighter than standard steel bearings normally used in the bicycle industry. When comparing the CeramicSpeed Balls with other ceramic balls in the industry, you will find that the CeramicSpeed Balls are 15% harder, take 99% higher loads, and are 100% smoother. - Inner Diameter: 12mm - Outer Diameter: 24mm - Width: 6mm

All CeramicSpeed Bearings are hand-built in Denmark. Super-smooth CeramicSpeed grade 3 Silicone Nitride balls are matched (within microns) with hardened steel raceways that feature an ultra-smooth polished groove. The balls are held in place by a reinforced polyamide cage. Every bearing is optimized with a low-viscosity CeramicSpeed All Round Grease to minimize friction and increase bearing life. Non-contact seals complete the bearings, keeping dirt and moisture out. CeramicSpeed Bearings can be used for any cycling discipline: Road, TT, Tri, Track, Cross, and MTB. The benefits are super low friction, better power transfer, and increased bearing life. During the building process, we check each bearing four times by hand to ensure that all parts are matched perfectly. CeramicSpeed Balls are 400% smoother, 128% harder, and 58% lighter than standard steel bearings normally used in the bicycle industry. When comparing the CeramicSpeed Balls with other ceramic balls in the industry, you will find that the CeramicSpeed Balls are 15% harder, take 99% higher loads, and are 100% smoother. - Inner Diameter: 17mm - Outer Diameter: 30mm - Width: 7mm

The all new Crank Brothers Highline remote kit. - Universal mounting system: top/bottom & left/right - Single bolt hinge locking system - Infinite spherical adjustment - Compatible with: Highline and other cable-actuated dropper seatposts

Service your DT Swiss star ratchet hubs and wheels with DT Swiss Ratchet and Kits. - DT Swiss Star Ratchet Kit - 24T

DT Swiss Sinc Ceramic cartridge bearings. - The black dust cover is intended to be installed facing the hub and the tan seal is intended to face externally

DT Swiss Sinc Ceramic cartridge bearings. - The black dust cover is intended to be installed facing the hub and the tan seal is intended to face externally

DT Swiss Sinc Ceramic cartridge bearings. - The black dust cover is intended to be installed facing the hub and the tan seal is intended to face externally

Transfer Dropper Post Remote A lightweight below-the-bar design for 1x drivetrains. FOX Transfer post levers provide smooth action and reduced force, providing consistent actuation pressure to raise or lower the seat. - 22.2 1x Remote I-Spec EV

Sport brake housing packs high performance features into a colorful and durable package, making it a functional and aesthetic upgrade. - Slick-Lube lined housing reduces friction for faster cable movement and better braking response - High carbon internal steel coil for improved stiffness - Appropriate for Teflon coated cables as well as steel and galvanized - Length: 10m

Pro Compressionless brake housing eliminates flex from cable actuated braking systems, increasing power and improving lever feel. - KEB-SL - linear strand, Kevlar reinforced, compressionless brake housing with Slick-Lube liner - Perfect for full-housing, high-performance bikes with mechanical disc or rim brakes - 20 black alloy lined end caps, 10 black POP end caps included

Cartridges fully replace the functional mechanism of KS dropper posts. Pick the model and length of drop for the post you need to service. These are also called "Oil Pressure Sticks" and "Air Pressure Sticks" In KS Service Documentation. - Fully replace the functional mechanism of KS dropper posts - May not work with OEM dropper posts

Cartridges fully replace the functional mechanism of KS dropper posts. Pick the model and length of drop for the post you need to service. These are also called "Oil Pressure Sticks" and "Air Pressure Sticks" In KS Service Documentation. - Fully replace the functional mechanism of KS dropper posts - May not work with OEM dropper posts

Saddle clamp heads and lowers for KS Dropper posts.

Replacement lever blades for Magura disc brakes

Master cylinder assemblies for Magura brakes include a master cylinder, lever blade and handlebar clamp. Hose fittings and line are sold separately. Flip flop design allows unit to be mounted to either the left or right side.

Magura service kits come in a variety of packages to fit your needs.

Magura service kits come in a variety of packages to fit your needs.

Master cylinder assemblies for Magura brakes include a master cylinder, lever blade and handlebar clamp. Hose fittings and line are sold separately. Flip flop design allows unit to be mounted to either the left or right side.

- Retrofits all Absolute damping forks (sold by fork year/model) - Separate thumb-operated lock and release buttons - Die-cast alloy body with forged alloy lever

• Machined aluminum mounting arm • Delrin (engineering grade thermoplastic) chain guide body • Adjustable design • Fits 32T to 38T chainrings • Compatible with 1x drivetrain systems • Clamp mount: 31.8-34.9mm • Weight: 75g (BB Mount), 88g (clamp mount), 80g (Mini)

- Provides enhanced chain retention for all 1x drivetrain systems - CNC-machined AL6061 alloy mount with dual-compound chain guide - Co-molded composite and TPR guide plates greatly reduce noise from chain contact - Compatible with 28-38T circular and 26-36T oval chainrings - Boost-compatible - Easily adjustable - Mounting hardware included